Stairs & Railings
Stair Refinishing in Weston, NJ
Stairs take more wear per square foot than any floor in the house, and they are sanded almost entirely by hand. In Weston, NJ the median home dates to 2009 and 0.0% of the housing predates 1940, which changes what Deco Hardwood Floor expects to find before the work starts.
Refinishing the one solid thing in a newer house
In Weston the stair is often the only solid wood in the house, and it takes more wear per square foot than any floor.
When the floors are engineered wood or vinyl plank, they are replaced at the end of their life. The stair is different. Solid treads can be sanded and finished again, and the finish can be built for the traffic a stair gets.
Most requests in newer houses are for a color change, to match flooring that was replaced, or for a tougher finish on treads where the builder's coat wore through in a few years.
Before you get a quote
A stair finished in a glossy coat shows every scuff and can be slippery in socks. We usually recommend a satin sheen on treads, and show both before you choose.
How the housing in Weston compares
Of the 1,250 housing units in Weston, roughly 0 were built before 1940 and approximately 20 before 1978.
That makes the housing here newer than the 30 Somerset County towns in our data taken together, where approximately 38.4% of 166,564 units predate 1978, and below the 60.5% figure for our whole service area. By the share built before 1940, Weston ranks 30th of those 30. The full table is published as open housing data.
| Place | Miles away | Median year built | Built before 1940 |
|---|---|---|---|
| Weston | 0 | 2009 | 0.0% |
| Manville | 1.5 | 1955 | 19.2% |
| Middlebush | 2.5 | 1976 | 6.7% |
| Finderne | 2.7 | 1971 | 9.8% |
| Blackwells Mills | 3.1 | 1990 | 2.2% |
For stair refinishing, the pre-1978 share is the figure that matters. Painted risers and balusters in those houses are sanded under the federal lead rule.
What is usually under the floor here
Engineered wood or vinyl plank, with rarely enough solid material to refinish.
Newer construction leans on engineered wood and rigid-core vinyl. Both are built to be stable over concrete and both are built to be replaced rather than restored.
That shifts what we do here. The work in this stock is installation, repair of damaged sections, and stairs, which are the one part of a new house that is still built from solid material and still worth refinishing.
Worth knowing here
Slab construction is common in newer housing, and a slab has to be tested for moisture before any wood goes on it. That test is a number, not an opinion.
Most of the housing here postdates the federal lead rule
Approximately 1.4% of the homes here were built before 1978, so most addresses fall outside it.
The EPA rule covers paid work disturbing painted surfaces in pre-1978 housing. In newer stock most addresses sit outside it, which simplifies how the work is staged.
It does not change how we sand. Vacuum extraction at the machine is how our equipment runs regardless, because the difference in the room is obvious whether or not a regulation is involved.
How stair refinishing runs
We look at the nosings
That is where wear shows first, and it decides refinish versus retread.Structure checked
Loose treads and squeaks addressed before finishing, because finish does not fix movement.Sanding, mostly by hand
Machines where they reach, hand work everywhere else.Finish applied
Coats on the cure schedule of the specified product.Staged so you can use the house
Where there is only one staircase, the schedule is built around that.
What stair refinishing includes, and what it does not
Stair refinishing covers checking the structure, sanding the treads, risers and visible stringer, and applying stain and finish. It does not put wood back where the nosing has worn away, and balusters are a separate decision because each one is done by hand.
Included
- A look at every nosing, to confirm the treads can be refinished.
- Loose treads and squeaks addressed before any finish is applied.
- Sanding of treads, risers and the visible stringer, by machine where it reaches and by hand elsewhere.
- A stain sample tested against your existing floor before the stair is stained.
- Finish coats applied by hand, on the cure schedule of the product.
- A schedule built around access when the house has only one staircase.
Not included, or quoted separately
- New treads. If the nosing is worn into the wood, that is retreading and a different quote.
- Balusters, unless you ask for them. Each one is sanded by hand, and it adds real time.
- A promise of a house without dust. Vacuum extraction catches most of it, not all of it.
What changes the price of stair refinishing
The price is set after we see the stair, not from its square footage. It moves most with the number of steps, with whether the balusters are refinished too, and with what has to come off the wood before new finish can go on.
| What changes it | How it moves the price | Example |
|---|---|---|
| Number of steps | Each step is a tread, a riser and several inside corners worked by hand, so the count of steps drives the hours. | A flight of fourteen risers has fourteen horizontal surfaces, fourteen vertical ones and a corner at every joint. |
| Balusters in or out | Refinishing balusters means sanding and coating each one by hand. Painting them, or leaving them alone, removes most of that time. | Treads and handrail refinished, with risers and balusters painted, is a common and faster version of the same job. |
| What is on the wood | Paint, old carpet staples and tack strip holes take more work to deal with than a worn clear finish, and all of it comes before stain. | A hardwood stair that was painted or carpeted over needs more preparation than one with a tired coat of polyurethane. |
| Open or closed stair | An open side adds the tread returns and the outside face of the stringer, plus more edges to work around the balusters. | A stair between two walls has fewer surfaces than one open to a hallway with balusters set into every tread. |
| Color change and finish type | Changing the color adds stain and sample work. The finish chosen sets the cure time between coats, which sets how the job is staged. | Waterborne finish lets you back on the stair far sooner than oil-modified polyurethane, so the two are scheduled differently. |
The full method, the equipment and what we will and will not promise are on the service page: Stair Refinishing.
Also in Weston
Hardwood Floor Refinishing
Sand the old finish off, repair what needs repairing, and put a new finish down
Dustless Floor Sanding
Vacuum-extraction sanding
Solid Hardwood Floor Installation
Solid wood, nailed down over a wood subfloor
Engineered Hardwood Installation
Real wood over a stable core
Luxury Vinyl Plank (LVP) Installation
Waterproof, quiet, and it does not care about a wet basement
Custom Stair Installation
Treads, risers, stringers and skirt board, built to a drawing instead of a catalog page
Hardwood Floor Repair
Board replacement, weaving in new wood, squeaks, gaps and cupping
Why homeowners hire Deco Hardwood Floor
Deco Hardwood Floor is owner operated: the person who quotes stair refinishing in Weston is the person responsible for it, and the material comes with the labor in one number.
Material and labor in one number
We buy the flooring direct from the distributor and pass the store price through, so you are not sourcing wood on your own between quotes.
Samples come to your house
Samples and larger offcuts come to you, so the color gets chosen in your own light instead of under a showroom lamp.
Stairs and railings built in house
Treads, risers, handrails and newel posts are drawn and built by our own crew. Most flooring crews subcontract stair work or decline it.
The owner quotes the job
The person who measures your floor is the person responsible for the work. There is no salesperson in between.
Measured before it is promised
Remaining thickness is measured at the edge of a board before we say a floor can be sanded, and no price is firm before we have seen the room.
Told straight, including the limits
Vacuum extraction catches most of the sanding dust and not all of it. We tell you that before the job instead of after.
More about who we are and what we will not claim on the About Deco Hardwood Floor page.
Questions about stair refinishing in Weston
What should we do before the crew arrives to refinish the stairs?
Clear the stair and both landings, and decide which floor each person will be on while coats cure. Before stair refinishing starts, take down pictures on the stair wall and move what you need for the day to the right level. Close off rooms that open onto the stair. Deco Hardwood Floor tells you the schedule before starting, so the closed periods are not a surprise.
Can you refinish stairs without doing the whole floor?
Yes, and it is common. Matching the new stair finish to an existing floor finish is the part that takes care, and it gets tested on a sample first.
My treads are worn through at the front edge. Can they still be refinished?
If the wear has gone into the wood at the nosing, sanding it flat removes the profile. At that point retreading, which is fitting new hardwood treads over the existing structure, is usually the better answer.
How long will the stairs be out of use?
It depends on the finish. Waterborne products let you back on far sooner than oil-modified polyurethane. Where the house has one staircase we tell you the schedule before starting.
Do you actually work in Weston?
Yes. Weston sits 40.6 miles from our base in Philadelphia, inside the area we cover. We quote the job before we schedule it, so you know the answer before anyone commits.
Can you tell me what my floor needs over the phone?
We can tell you what is likely, and this page is most of that answer. What we cannot do is quote a floor we have not seen, because remaining thickness and what is under the covering both decide the job and neither is visible in a description.
Do you bring the material?
Yes. We buy direct from the distributor and the material lands in the same number as the labor. Samples and larger offcuts come to the house so you choose in your own light.
Is there anything worth refinishing in a newer house?
The stairs, usually. They are still built from solid material in most construction, they take more wear per square foot than any floor, and they are the one surface where refinishing beats replacing.
Stair Refinishing near Weston
Send a photo and we will tell you what you are looking at
Stair Refinishing in Weston starts with someone reading the house. We quote every job ourselves, with no salesperson in between, and a photo of the floor gets you a straight answer faster than a form does.
